PEDALTRAIN martin acoustic guitar strings CLASSIC dreadnought acoustic guitar 1 martin guitar strings acoustic medium PEDALBOARD martin strings acoustic w/ martin guitars TOUR CASE & VOODOO LAB PEDAL POWER + MOUNTED

Tour Case:

23.5 x 14.7 x 8.25 inches (59.7 x 37.3 x 20.9 cm)

15 lbs (6.8 kg)





Included: 

88 inches (244 cm) Pedaltrain’s professional grade adhesive backed hook-and-loop for securing pedalsAssortment of zip ties for organizing and securing cables



Input

IEC connector:

120V 50/60Hz (North America)


Output

5.5x2.1mm barrel connectors - center negative
Six 9VDC 100mA regulated
Two 9VDC 250mA regulated
Four selectable for Boss ACA
Two selectable for Line6 Modelers
Two adjustable sag 4 to 9V
Short circuit protected 


Included Cables

5.5x2.1mm right angle barrel connectors (6)
5.5x2.1mm straight barrel connectors (2)
5.5x2.5mm “red” barrel for L6 (1)
3.5mm mini plug for vintage MXR or Electro-Harmonix (1)
9V battery snap for pedals without a power jack (1)

Physical6" wide x 3.4" deep x 1.75" tall (152x86x45mm)Weight2 lbs. (0.9 kg)Special

Toroidal power transformer
Rear Courtesy Auxiliary AC outlet, 200 watts max

Warranty5 years




9/12V (x4) – Standard 9V and 12V Boss ACA 
With each one of these four outputs delivering 100mA, you can easily power any 9V battery-operated pedals. Boss pedals that specify the PSA adapter operate at 9V like most other pedals. Boss pedals that require the ACA adapter operate at 12V which can be selected via switches underneath the Pedal Power 2 Plus. Any one of these outputs can be individually selected to run at 9V or 12V. 

9V (x2) – High Current 9V and Line 6 Modelers 
These two outputs each deliver 250mA allowing you to run high current draw effects like the Boss DD-20 Giga Delay or Line 6 DL4 Delay Modeler. Via switches underneath the Pedal Power 2 Plus, these two outputs can be separately configured for regulated (Boss Twin Pedals) or unregulated (Line 6 Modelers) power allowing you to run both units if so desired. These outputs can also power any standard 9V effects as well.   

9V (x2) – Standard 9V With Battery Sag Control
These outputs each have an available 100mA of power, but also allow you to SAG the voltage from roughly 4V to 9V. This feature can be enabled via the bottom panel switches. The SAG control is mostly useful for transistor-based fuzz, octavia, and distortion circuits, as most modern opamp designs are minimally affected by variations in supply voltage. We recommend turning SAG off if you’re going to run digital pedals like delay, chorus, and reverb.

18V/24V – Using Custom Cables 
All of the outputs on the Pedal Power 2 Plus (and the original Pedal Power) are completely isolated allowing you to create different voltages. You can run effects like the current MXR Flanger by combining two 9V outputs to create a single 18V supply. By switching two outputs into 12V ACA mode, you can join them together to create a 24V output for powering numerous Electro-Harmonix stompboxes including the Deluxe Memory Man. 




Shipping:
Item will ship by UPS, shipping is FREE to the lower 48 states.

We will also ship to HI, PR, & AK, & Worldwide. Please email address for shipping rates.

Payment:

Buyer Can Call TOLL FREE
1-800-573-7271 with Visa, Mastercard and American Express.
We also accept Payment Online with Credit / Debit Card or Electronic Check at

 www.paypal.com  . 


Click Here. Double your traffic. Get Vendio Gallery - Now FREE!